Tjernlund MAC1E Control Version F (Compatible with UC1 Contr Manual do Utilizador descarregar pdf (Página 2)

MAC1E WIRING CONNECTIONS WITH UC1 UNIVERSAL CONTROL

Remove power to UC1 and heating equipment when making connections from the MAC1E to the UC1 or installing, servicing or changing dip switch settings in the UC1. Failure to do so may result in

personal injury and/or equipment damage. The Power LED (RED) on UC1 or any LED’s on UC1 or MAC1E should not be on.

See UC1 Universal Control wiring section of Venter or UC1 instructions for 24 VAC, 115 VAC or Millivolt (Dry Contact) appliance interlock diagrams. The MAC1E and UC1 Universal

Control appliance interlock steps and diagrams are identical.

MAC1E SAFETY INTERLOCK TEST

PROVER

LED1

LED

POWER

RED

24 OR 115 VAC

APPROVED CALL BACK TO HEATER

INTERCEPTED CALL COMMON OR NEUTRAL

24 OR 115 VAC INTERCEPTED CALL FOR HEAT

5 VDC BOARD-GENERATED POWER

DO NOT SUPPLY POWER!

115 VAC

LEGEND:

TERMINAL 2:

TERMINAL 1:

TERMINAL 4:

LED6

VENTER / INDUCER

1 H.P. MAX @ 115 VAC

MOTOR

50/60 Hz

115 VAC

SUPPLY

CEPTED

CALL FOR

HEAT

INTER-

NEUTRAL

LINE / HOT

COMMON /

"DRY"

CALL SWITCH

USER-PROVIDED

APPROVED APPROVED

USER-PROVIDED

CALL SWITCH

"DRY"

COMMON /

LINE / HOT

NEUTRAL

INTER-

HEAT

CALL FOR

CEPTED

DO NOT SUPPLY VOLTAGE

TO "A" OR "B".

GREEN

RED

CALL

JUMPER

INTERLOCK

COM

RELAY

DRY

IMPORTANT:

115V

24V

LED5 LED3LED4

P/N 1303962A

AMBER

(9)

(3 - 8)

GND

(1 - 2)

4532

Burner circuit is energized with contact closure from terminal 3 to terminal 4.

24" FLEX

CONDUIT

MAC1E

Safety circuit through Universal Control P1 & P2 Fan Prover is verified "Open" upon start up.

Appliance call for heat.

LED STATUS INDICATOR LIGHTS

LED #2 (Blue)

installing or servicing the MAC1E. Failure to do so may result in personal

injury and/or equipment damage.

TJERNLUND

PRODUCTS,

INC.

TO "A" OR "B".

DO NOT SUPPLY VOLTAGE

115V

MAC1E CONTROL

RED JUMPER POSITION MUST BE THE SAME

AMBER

BLUE

CALL

INTERLOCK

RELAY

JUMPER

COM

APPLIANCE "GO"

APPLIANCE CALL

AS APPLIANCE INTERLOCK VOLTAGE.

24V

DRY

IMPORTANT:

LED1LED2

FGND

post-purge settings + safety circuit connections are in the Universal Control.

This device must be connected to a Tjernlund Universal Control. All pre and

Remove power to Universal Control and all connected appliances when

NOTE:

WARNING:

LED #1 (Amber)

BLUE

LED2

UNIVERSAL CONTROL

PRE-PURGE SETTINGS

OPEN PROVER OPTION

POST-PURGE SETTINGS

AS APPLIANCE INTERLOCK VOLTAGE.

RED JUMPER POSITION MUST BE THE SAME

TJERNLUND

INC.

PRODUCTS,

MTR

LED

POWER

RED

LED6

Connect Black from MAC1E whip to XL on UC1.

Connect White from MAC1E whip to XN on UC1.

Connect Violet from MAC1E whip to C on UC1

Connect Gray from MAC1E whip to GND on UC1.

Connect Red from MAC1E whip to F on UC1.

Connect Green from MAC1E whip to ground in UC1.

IMPORTANT: Venter Fan Prover must be wired to

P1 and P2 safety circuit in UC1.

RED appliance interlock voltage jumper in MAC1E

and UC1 must be positioned based on the control

voltage of the appliance interlocked with each control

115V, 24V or DRY.

1 2

Comentários a estes Manuais

Sem comentários

Tjernlund MAC1E Control Version F (Compatible with UC1 Contr Manual do Utilizador Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento Tjernlund MAC1E Control Version F (Compatible with UC1 Contr